You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
174 lines
6.2 KiB
174 lines
6.2 KiB
Using the RAM disk block device with Linux |
|
------------------------------------------ |
|
|
|
Contents: |
|
|
|
1) Overview |
|
2) Kernel Command Line Parameters |
|
3) Using "rdev -r" |
|
4) An Example of Creating a Compressed RAM Disk |
|
|
|
|
|
1) Overview |
|
----------- |
|
|
|
The RAM disk driver is a way to use main system memory as a block device. It |
|
is required for initrd, an initial filesystem used if you need to load modules |
|
in order to access the root filesystem (see Documentation/admin-guide/initrd.rst). It can |
|
also be used for a temporary filesystem for crypto work, since the contents |
|
are erased on reboot. |
|
|
|
The RAM disk dynamically grows as more space is required. It does this by using |
|
RAM from the buffer cache. The driver marks the buffers it is using as dirty |
|
so that the VM subsystem does not try to reclaim them later. |
|
|
|
The RAM disk supports up to 16 RAM disks by default, and can be reconfigured |
|
to support an unlimited number of RAM disks (at your own risk). Just change |
|
the configuration symbol BLK_DEV_RAM_COUNT in the Block drivers config menu |
|
and (re)build the kernel. |
|
|
|
To use RAM disk support with your system, run './MAKEDEV ram' from the /dev |
|
directory. RAM disks are all major number 1, and start with minor number 0 |
|
for /dev/ram0, etc. If used, modern kernels use /dev/ram0 for an initrd. |
|
|
|
The new RAM disk also has the ability to load compressed RAM disk images, |
|
allowing one to squeeze more programs onto an average installation or |
|
rescue floppy disk. |
|
|
|
|
|
2) Parameters |
|
--------------------------------- |
|
|
|
2a) Kernel Command Line Parameters |
|
|
|
ramdisk_size=N |
|
============== |
|
|
|
This parameter tells the RAM disk driver to set up RAM disks of N k size. The |
|
default is 4096 (4 MB). |
|
|
|
2b) Module parameters |
|
|
|
rd_nr |
|
===== |
|
/dev/ramX devices created. |
|
|
|
max_part |
|
======== |
|
Maximum partition number. |
|
|
|
rd_size |
|
======= |
|
See ramdisk_size. |
|
|
|
3) Using "rdev -r" |
|
------------------ |
|
|
|
The usage of the word (two bytes) that "rdev -r" sets in the kernel image is |
|
as follows. The low 11 bits (0 -> 10) specify an offset (in 1 k blocks) of up |
|
to 2 MB (2^11) of where to find the RAM disk (this used to be the size). Bit |
|
14 indicates that a RAM disk is to be loaded, and bit 15 indicates whether a |
|
prompt/wait sequence is to be given before trying to read the RAM disk. Since |
|
the RAM disk dynamically grows as data is being written into it, a size field |
|
is not required. Bits 11 to 13 are not currently used and may as well be zero. |
|
These numbers are no magical secrets, as seen below: |
|
|
|
./arch/x86/kernel/setup.c:#define RAMDISK_IMAGE_START_MASK 0x07FF |
|
./arch/x86/kernel/setup.c:#define RAMDISK_PROMPT_FLAG 0x8000 |
|
./arch/x86/kernel/setup.c:#define RAMDISK_LOAD_FLAG 0x4000 |
|
|
|
Consider a typical two floppy disk setup, where you will have the |
|
kernel on disk one, and have already put a RAM disk image onto disk #2. |
|
|
|
Hence you want to set bits 0 to 13 as 0, meaning that your RAM disk |
|
starts at an offset of 0 kB from the beginning of the floppy. |
|
The command line equivalent is: "ramdisk_start=0" |
|
|
|
You want bit 14 as one, indicating that a RAM disk is to be loaded. |
|
The command line equivalent is: "load_ramdisk=1" |
|
|
|
You want bit 15 as one, indicating that you want a prompt/keypress |
|
sequence so that you have a chance to switch floppy disks. |
|
The command line equivalent is: "prompt_ramdisk=1" |
|
|
|
Putting that together gives 2^15 + 2^14 + 0 = 49152 for an rdev word. |
|
So to create disk one of the set, you would do: |
|
|
|
/usr/src/linux# cat arch/x86/boot/zImage > /dev/fd0 |
|
/usr/src/linux# rdev /dev/fd0 /dev/fd0 |
|
/usr/src/linux# rdev -r /dev/fd0 49152 |
|
|
|
If you make a boot disk that has LILO, then for the above, you would use: |
|
append = "ramdisk_start=0 load_ramdisk=1 prompt_ramdisk=1" |
|
Since the default start = 0 and the default prompt = 1, you could use: |
|
append = "load_ramdisk=1" |
|
|
|
|
|
4) An Example of Creating a Compressed RAM Disk |
|
---------------------------------------------- |
|
|
|
To create a RAM disk image, you will need a spare block device to |
|
construct it on. This can be the RAM disk device itself, or an |
|
unused disk partition (such as an unmounted swap partition). For this |
|
example, we will use the RAM disk device, "/dev/ram0". |
|
|
|
Note: This technique should not be done on a machine with less than 8 MB |
|
of RAM. If using a spare disk partition instead of /dev/ram0, then this |
|
restriction does not apply. |
|
|
|
a) Decide on the RAM disk size that you want. Say 2 MB for this example. |
|
Create it by writing to the RAM disk device. (This step is not currently |
|
required, but may be in the future.) It is wise to zero out the |
|
area (esp. for disks) so that maximal compression is achieved for |
|
the unused blocks of the image that you are about to create. |
|
|
|
dd if=/dev/zero of=/dev/ram0 bs=1k count=2048 |
|
|
|
b) Make a filesystem on it. Say ext2fs for this example. |
|
|
|
mke2fs -vm0 /dev/ram0 2048 |
|
|
|
c) Mount it, copy the files you want to it (eg: /etc/* /dev/* ...) |
|
and unmount it again. |
|
|
|
d) Compress the contents of the RAM disk. The level of compression |
|
will be approximately 50% of the space used by the files. Unused |
|
space on the RAM disk will compress to almost nothing. |
|
|
|
dd if=/dev/ram0 bs=1k count=2048 | gzip -v9 > /tmp/ram_image.gz |
|
|
|
e) Put the kernel onto the floppy |
|
|
|
dd if=zImage of=/dev/fd0 bs=1k |
|
|
|
f) Put the RAM disk image onto the floppy, after the kernel. Use an offset |
|
that is slightly larger than the kernel, so that you can put another |
|
(possibly larger) kernel onto the same floppy later without overlapping |
|
the RAM disk image. An offset of 400 kB for kernels about 350 kB in |
|
size would be reasonable. Make sure offset+size of ram_image.gz is |
|
not larger than the total space on your floppy (usually 1440 kB). |
|
|
|
dd if=/tmp/ram_image.gz of=/dev/fd0 bs=1k seek=400 |
|
|
|
g) Use "rdev" to set the boot device, RAM disk offset, prompt flag, etc. |
|
For prompt_ramdisk=1, load_ramdisk=1, ramdisk_start=400, one would |
|
have 2^15 + 2^14 + 400 = 49552. |
|
|
|
rdev /dev/fd0 /dev/fd0 |
|
rdev -r /dev/fd0 49552 |
|
|
|
That is it. You now have your boot/root compressed RAM disk floppy. Some |
|
users may wish to combine steps (d) and (f) by using a pipe. |
|
|
|
-------------------------------------------------------------------------- |
|
Paul Gortmaker 12/95 |
|
|
|
Changelog: |
|
---------- |
|
|
|
10-22-04 : Updated to reflect changes in command line options, remove |
|
obsolete references, general cleanup. |
|
James Nelson (james4765@gmail.com) |
|
|
|
|
|
12-95 : Original Document
|
|
|