You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
798 lines
25 KiB
798 lines
25 KiB
# |
|
# USB Host Controller Drivers |
|
# |
|
comment "USB Host Controller Drivers" |
|
|
|
config USB_C67X00_HCD |
|
tristate "Cypress C67x00 HCD support" |
|
help |
|
The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role |
|
host/peripheral/OTG USB controllers. |
|
|
|
Enable this option to support this chip in host controller mode. |
|
If unsure, say N. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called c67x00. |
|
|
|
config USB_XHCI_HCD |
|
tristate "xHCI HCD (USB 3.0) support" |
|
---help--- |
|
The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0 |
|
"SuperSpeed" host controller hardware. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called xhci-hcd. |
|
|
|
if USB_XHCI_HCD |
|
|
|
config USB_XHCI_PCI |
|
tristate |
|
depends on PCI |
|
default y |
|
|
|
config USB_XHCI_PLATFORM |
|
tristate "Generic xHCI driver for a platform device" |
|
---help--- |
|
Adds an xHCI host driver for a generic platform device, which |
|
provides a memory space and an irq. |
|
It is also a prerequisite for platform specific drivers that |
|
implement some extra quirks. |
|
|
|
If unsure, say N. |
|
|
|
config USB_XHCI_MTK |
|
tristate "xHCI support for Mediatek MT65xx" |
|
select MFD_SYSCON |
|
depends on ARCH_MEDIATEK || COMPILE_TEST || MEDIATEK_SOLUTION |
|
---help--- |
|
Say 'Y' to enable the support for the xHCI host controller |
|
found in Mediatek MT65xx SoCs. |
|
If unsure, say N. |
|
|
|
config USB_XHCI_MVEBU |
|
tristate "xHCI support for Marvell Armada 375/38x" |
|
select USB_XHCI_PLATFORM |
|
depends on ARCH_MVEBU || COMPILE_TEST |
|
---help--- |
|
Say 'Y' to enable the support for the xHCI host controller |
|
found in Marvell Armada 375/38x ARM SOCs. |
|
|
|
config USB_XHCI_RCAR |
|
tristate "xHCI support for Renesas R-Car SoCs" |
|
select USB_XHCI_PLATFORM |
|
depends on ARCH_SHMOBILE || COMPILE_TEST |
|
---help--- |
|
Say 'Y' to enable the support for the xHCI host controller |
|
found in Renesas R-Car ARM SoCs. |
|
|
|
endif # USB_XHCI_HCD |
|
|
|
config USB_EHCI_HCD |
|
tristate "EHCI HCD (USB 2.0) support" |
|
---help--- |
|
The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0 |
|
"high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware. |
|
If your USB host controller supports USB 2.0, you will likely want to |
|
configure this Host Controller Driver. |
|
|
|
EHCI controllers are packaged with "companion" host controllers (OHCI |
|
or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports |
|
will connect to EHCI if the device is high speed, otherwise they |
|
connect to a companion controller. If you configure EHCI, you should |
|
probably configure the OHCI (for NEC and some other vendors) USB Host |
|
Controller Driver or UHCI (for Via motherboards) Host Controller |
|
Driver too. |
|
|
|
You may want to read <file:Documentation/usb/ehci.txt>. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called ehci-hcd. |
|
|
|
config USB_EHCI_ROOT_HUB_TT |
|
bool "Root Hub Transaction Translators" |
|
depends on USB_EHCI_HCD |
|
---help--- |
|
Some EHCI chips have vendor-specific extensions to integrate |
|
transaction translators, so that no OHCI or UHCI companion |
|
controller is needed. It's safe to say "y" even if your |
|
controller doesn't support this feature. |
|
|
|
This supports the EHCI implementation that's originally |
|
from ARC, and has since changed hands a few times. |
|
|
|
config USB_EHCI_TT_NEWSCHED |
|
bool "Improved Transaction Translator scheduling" |
|
depends on USB_EHCI_HCD |
|
default y |
|
---help--- |
|
This changes the periodic scheduling code to fill more of the low |
|
and full speed bandwidth available from the Transaction Translator |
|
(TT) in USB 2.0 hubs. Without this, only one transfer will be |
|
issued in each microframe, significantly reducing the number of |
|
periodic low/fullspeed transfers possible. |
|
|
|
If you have multiple periodic low/fullspeed devices connected to a |
|
highspeed USB hub which is connected to a highspeed USB Host |
|
Controller, and some of those devices will not work correctly |
|
(possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if |
|
you have only one such device and it doesn't work, you could try |
|
saying N. |
|
|
|
If unsure, say Y. |
|
|
|
config USB_FSL_MPH_DR_OF |
|
tristate |
|
|
|
if USB_EHCI_HCD |
|
|
|
config USB_EHCI_PCI |
|
tristate |
|
depends on PCI |
|
default y |
|
|
|
config USB_EHCI_HCD_PMC_MSP |
|
tristate "EHCI support for on-chip PMC MSP71xx USB controller" |
|
depends on MSP_HAS_USB |
|
default n |
|
select USB_EHCI_BIG_ENDIAN_DESC |
|
select USB_EHCI_BIG_ENDIAN_MMIO |
|
---help--- |
|
Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's. |
|
If unsure, say N. |
|
|
|
config XPS_USB_HCD_XILINX |
|
bool "Use Xilinx usb host EHCI controller core" |
|
depends on (PPC32 || MICROBLAZE) |
|
select USB_EHCI_BIG_ENDIAN_DESC |
|
select USB_EHCI_BIG_ENDIAN_MMIO |
|
---help--- |
|
Xilinx xps USB host controller core is EHCI compliant and has |
|
transaction translator built-in. It can be configured to either |
|
support both high speed and full speed devices, or high speed |
|
devices only. |
|
|
|
config USB_EHCI_FSL |
|
tristate "Support for Freescale PPC on-chip EHCI USB controller" |
|
depends on FSL_SOC |
|
select USB_EHCI_ROOT_HUB_TT |
|
select USB_FSL_MPH_DR_OF if OF |
|
---help--- |
|
Variation of ARC USB block used in some Freescale chips. |
|
|
|
config USB_EHCI_MXC |
|
tristate "Support for Freescale i.MX on-chip EHCI USB controller" |
|
depends on ARCH_MXC |
|
select USB_EHCI_ROOT_HUB_TT |
|
---help--- |
|
Variation of ARC USB block used in some Freescale chips. |
|
|
|
config USB_EHCI_HCD_OMAP |
|
tristate "EHCI support for OMAP3 and later chips" |
|
depends on ARCH_OMAP |
|
select NOP_USB_XCEIV |
|
default y |
|
---help--- |
|
Enables support for the on-chip EHCI controller on |
|
OMAP3 and later chips. |
|
|
|
config USB_EHCI_HCD_ORION |
|
tristate "Support for Marvell EBU on-chip EHCI USB controller" |
|
depends on USB_EHCI_HCD && PLAT_ORION |
|
default y |
|
---help--- |
|
Enables support for the on-chip EHCI controller on Marvell's |
|
embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP, |
|
Armada 370. This is different from the EHCI implementation |
|
on Marvell's mobile PXA and MMP SoC, see "EHCI support for |
|
Marvell PXA/MMP USB controller" for those. |
|
|
|
config USB_EHCI_HCD_SPEAR |
|
tristate "Support for ST SPEAr on-chip EHCI USB controller" |
|
depends on USB_EHCI_HCD && PLAT_SPEAR |
|
default y |
|
---help--- |
|
Enables support for the on-chip EHCI controller on |
|
ST SPEAr chips. |
|
|
|
config USB_EHCI_HCD_STI |
|
tristate "Support for ST STiHxxx on-chip EHCI USB controller" |
|
depends on ARCH_STI && OF |
|
select GENERIC_PHY |
|
select USB_EHCI_HCD_PLATFORM |
|
help |
|
Enable support for the on-chip EHCI controller found on |
|
STMicroelectronics consumer electronics SoC's. |
|
|
|
config USB_EHCI_HCD_AT91 |
|
tristate "Support for Atmel on-chip EHCI USB controller" |
|
depends on USB_EHCI_HCD && ARCH_AT91 |
|
default y |
|
---help--- |
|
Enables support for the on-chip EHCI controller on |
|
Atmel chips. |
|
|
|
config USB_EHCI_MSM |
|
tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller" |
|
depends on ARCH_QCOM |
|
select USB_EHCI_ROOT_HUB_TT |
|
---help--- |
|
Enables support for the USB Host controller present on the |
|
Qualcomm chipsets. Root Hub has inbuilt TT. |
|
This driver depends on OTG driver for PHY initialization, |
|
clock management, powering up VBUS, and power management. |
|
This driver is not supported on boards like trout which |
|
has an external PHY. |
|
|
|
config USB_EHCI_TEGRA |
|
tristate "NVIDIA Tegra HCD support" |
|
depends on ARCH_TEGRA |
|
select USB_EHCI_ROOT_HUB_TT |
|
select USB_PHY |
|
select USB_ULPI |
|
select USB_ULPI_VIEWPORT |
|
help |
|
This driver enables support for the internal USB Host Controllers |
|
found in NVIDIA Tegra SoCs. The controllers are EHCI compliant. |
|
|
|
config USB_EHCI_HCD_PPC_OF |
|
bool "EHCI support for PPC USB controller on OF platform bus" |
|
depends on PPC |
|
default y |
|
---help--- |
|
Enables support for the USB controller present on the PowerPC |
|
OpenFirmware platform bus. |
|
|
|
config USB_EHCI_SH |
|
bool "EHCI support for SuperH USB controller" |
|
depends on SUPERH |
|
---help--- |
|
Enables support for the on-chip EHCI controller on the SuperH. |
|
If you use the PCI EHCI controller, this option is not necessary. |
|
|
|
config USB_EHCI_EXYNOS |
|
tristate "EHCI support for Samsung S5P/EXYNOS SoC Series" |
|
depends on ARCH_S5PV210 || ARCH_EXYNOS |
|
help |
|
Enable support for the Samsung Exynos SOC's on-chip EHCI controller. |
|
|
|
config USB_EHCI_MV |
|
bool "EHCI support for Marvell PXA/MMP USB controller" |
|
depends on (ARCH_PXA || ARCH_MMP) |
|
select USB_EHCI_ROOT_HUB_TT |
|
---help--- |
|
Enables support for Marvell (including PXA and MMP series) on-chip |
|
USB SPH and OTG controller. SPH is a single port host, and it can |
|
only be EHCI host. OTG is controller that can switch to host mode. |
|
Note that this driver will not work on Marvell's other EHCI |
|
controller used by the EBU-type SoCs including Orion, Kirkwood, |
|
Dova, Armada 370 and Armada XP. See "Support for Marvell EBU |
|
on-chip EHCI USB controller" for those. |
|
|
|
config USB_W90X900_EHCI |
|
tristate "W90X900(W90P910) EHCI support" |
|
depends on ARCH_W90X900 |
|
---help--- |
|
Enables support for the W90X900 USB controller |
|
|
|
config USB_CNS3XXX_EHCI |
|
bool "Cavium CNS3XXX EHCI Module (DEPRECATED)" |
|
depends on ARCH_CNS3XXX |
|
select USB_EHCI_HCD_PLATFORM |
|
---help--- |
|
This option is deprecated now and the driver was removed, use |
|
USB_EHCI_HCD_PLATFORM instead. |
|
|
|
Enable support for the CNS3XXX SOC's on-chip EHCI controller. |
|
It is needed for high-speed (480Mbit/sec) USB 2.0 device |
|
support. |
|
|
|
config USB_EHCI_ATH79 |
|
bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)" |
|
depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X) |
|
select USB_EHCI_ROOT_HUB_TT |
|
select USB_EHCI_HCD_PLATFORM |
|
default y |
|
---help--- |
|
This option is deprecated now and the driver was removed, use |
|
USB_EHCI_HCD_PLATFORM instead. |
|
|
|
Enables support for the built-in EHCI controller present |
|
on the Atheros AR7XXX/AR9XXX SoCs. |
|
|
|
config USB_EHCI_HCD_PLATFORM |
|
tristate "Generic EHCI driver for a platform device" |
|
default n |
|
---help--- |
|
Adds an EHCI host driver for a generic platform device, which |
|
provides a memory space and an irq. |
|
|
|
If unsure, say N. |
|
|
|
config USB_OCTEON_EHCI |
|
bool "Octeon on-chip EHCI support (DEPRECATED)" |
|
depends on CAVIUM_OCTEON_SOC |
|
default n |
|
select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN |
|
select USB_EHCI_HCD_PLATFORM |
|
help |
|
This option is deprecated now and the driver was removed, use |
|
USB_EHCI_HCD_PLATFORM instead. |
|
|
|
Enable support for the Octeon II SOC's on-chip EHCI |
|
controller. It is needed for high-speed (480Mbit/sec) |
|
USB 2.0 device support. All CN6XXX based chips with USB are |
|
supported. |
|
|
|
endif # USB_EHCI_HCD |
|
|
|
config USB_OXU210HP_HCD |
|
tristate "OXU210HP HCD support" |
|
---help--- |
|
The OXU210HP is an USB host/OTG/device controller. Enable this |
|
option if your board has this chip. If unsure, say N. |
|
|
|
This driver does not support isochronous transfers and doesn't |
|
implement OTG nor USB device controllers. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called oxu210hp-hcd. |
|
|
|
config USB_ISP116X_HCD |
|
tristate "ISP116X HCD support" |
|
---help--- |
|
The ISP1160 and ISP1161 chips are USB host controllers. Enable this |
|
option if your board has this chip. If unsure, say N. |
|
|
|
This driver does not support isochronous transfers. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called isp116x-hcd. |
|
|
|
config USB_ISP1362_HCD |
|
tristate "ISP1362 HCD support" |
|
---help--- |
|
Supports the Philips ISP1362 chip as a host controller |
|
|
|
This driver does not support isochronous transfers. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called isp1362-hcd. |
|
|
|
config USB_FOTG210_HCD |
|
tristate "FOTG210 HCD support" |
|
depends on USB |
|
---help--- |
|
Faraday FOTG210 is an OTG controller which can be configured as |
|
an USB2.0 host. It is designed to meet USB2.0 EHCI specification |
|
with minor modification. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called fotg210-hcd. |
|
|
|
config USB_MAX3421_HCD |
|
tristate "MAX3421 HCD (USB-over-SPI) support" |
|
depends on USB && SPI |
|
---help--- |
|
The Maxim MAX3421E chip supports standard USB 2.0-compliant |
|
full-speed devices either in host or peripheral mode. This |
|
driver supports the host-mode of the MAX3421E only. |
|
|
|
To compile this driver as a module, choose M here: the module will |
|
be called max3421-hcd. |
|
|
|
config USB_OHCI_HCD |
|
tristate "OHCI HCD (USB 1.1) support" |
|
---help--- |
|
The Open Host Controller Interface (OHCI) is a standard for accessing |
|
USB 1.1 host controller hardware. It does more in hardware than Intel's |
|
UHCI specification. If your USB host controller follows the OHCI spec, |
|
say Y. On most non-x86 systems, and on x86 hardware that's not using a |
|
USB controller from Intel or VIA, this is appropriate. If your host |
|
controller doesn't use PCI, this is probably appropriate. For a PCI |
|
based system where you're not sure, the "lspci -v" entry will list the |
|
right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called ohci-hcd. |
|
|
|
if USB_OHCI_HCD |
|
|
|
config USB_OHCI_HCD_OMAP1 |
|
tristate "OHCI support for OMAP1/2 chips" |
|
depends on ARCH_OMAP1 |
|
depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3) |
|
default y |
|
---help--- |
|
Enables support for the OHCI controller on OMAP1/2 chips. |
|
|
|
config USB_OHCI_HCD_SPEAR |
|
tristate "Support for ST SPEAr on-chip OHCI USB controller" |
|
depends on USB_OHCI_HCD && PLAT_SPEAR |
|
default y |
|
---help--- |
|
Enables support for the on-chip OHCI controller on |
|
ST SPEAr chips. |
|
|
|
config USB_OHCI_HCD_STI |
|
tristate "Support for ST STiHxxx on-chip OHCI USB controller" |
|
depends on ARCH_STI && OF |
|
select GENERIC_PHY |
|
select USB_OHCI_HCD_PLATFORM |
|
help |
|
Enable support for the on-chip OHCI controller found on |
|
STMicroelectronics consumer electronics SoC's. |
|
|
|
config USB_OHCI_HCD_S3C2410 |
|
tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series" |
|
depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX) |
|
default y |
|
---help--- |
|
Enables support for the on-chip OHCI controller on |
|
S3C24xx/S3C64xx chips. |
|
|
|
config USB_OHCI_HCD_LPC32XX |
|
tristate "Support for LPC on-chip OHCI USB controller" |
|
depends on USB_OHCI_HCD && ARCH_LPC32XX |
|
depends on USB_ISP1301 |
|
default y |
|
---help--- |
|
Enables support for the on-chip OHCI controller on |
|
NXP chips. |
|
|
|
config USB_OHCI_HCD_PXA27X |
|
tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller" |
|
depends on USB_OHCI_HCD && (PXA27x || PXA3xx) |
|
default y |
|
---help--- |
|
Enables support for the on-chip OHCI controller on |
|
PXA27x/PXA3xx chips. |
|
|
|
config USB_OHCI_HCD_AT91 |
|
tristate "Support for Atmel on-chip OHCI USB controller" |
|
depends on USB_OHCI_HCD && ARCH_AT91 && OF |
|
default y |
|
---help--- |
|
Enables support for the on-chip OHCI controller on |
|
Atmel chips. |
|
|
|
config USB_OHCI_HCD_OMAP3 |
|
tristate "OHCI support for OMAP3 and later chips" |
|
depends on (ARCH_OMAP3 || ARCH_OMAP4) |
|
default y |
|
---help--- |
|
Enables support for the on-chip OHCI controller on |
|
OMAP3 and later chips. |
|
|
|
config USB_OHCI_HCD_DAVINCI |
|
bool "OHCI support for TI DaVinci DA8xx" |
|
depends on ARCH_DAVINCI_DA8XX |
|
depends on USB_OHCI_HCD=y |
|
default y |
|
help |
|
Enables support for the DaVinci DA8xx integrated OHCI |
|
controller. This driver cannot currently be a loadable |
|
module because it lacks a proper PHY abstraction. |
|
|
|
config USB_OHCI_ATH79 |
|
bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)" |
|
depends on (SOC_AR71XX || SOC_AR724X) |
|
select USB_OHCI_HCD_PLATFORM |
|
default y |
|
help |
|
This option is deprecated now and the driver was removed, use |
|
USB_OHCI_HCD_PLATFORM instead. |
|
|
|
Enables support for the built-in OHCI controller present on the |
|
Atheros AR71XX/AR7240 SoCs. |
|
|
|
config USB_OHCI_HCD_PPC_OF_BE |
|
bool "OHCI support for OF platform bus (big endian)" |
|
depends on PPC |
|
select USB_OHCI_BIG_ENDIAN_DESC |
|
select USB_OHCI_BIG_ENDIAN_MMIO |
|
---help--- |
|
Enables support for big-endian USB controllers present on the |
|
OpenFirmware platform bus. |
|
|
|
config USB_OHCI_HCD_PPC_OF_LE |
|
bool "OHCI support for OF platform bus (little endian)" |
|
depends on PPC |
|
select USB_OHCI_LITTLE_ENDIAN |
|
---help--- |
|
Enables support for little-endian USB controllers present on the |
|
OpenFirmware platform bus. |
|
|
|
config USB_OHCI_HCD_PPC_OF |
|
bool |
|
depends on PPC |
|
default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE |
|
|
|
config USB_OHCI_HCD_PCI |
|
tristate "OHCI support for PCI-bus USB controllers" |
|
depends on PCI |
|
default y |
|
select USB_OHCI_LITTLE_ENDIAN |
|
---help--- |
|
Enables support for PCI-bus plug-in USB controller cards. |
|
If unsure, say Y. |
|
|
|
config USB_OHCI_HCD_SSB |
|
bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)" |
|
depends on (SSB = y || SSB = USB_OHCI_HCD) |
|
select USB_HCD_SSB |
|
select USB_OHCI_HCD_PLATFORM |
|
default n |
|
---help--- |
|
This option is deprecated now and the driver was removed, use |
|
USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead. |
|
|
|
Support for the Sonics Silicon Backplane (SSB) attached |
|
Broadcom USB OHCI core. |
|
|
|
This device is present in some embedded devices with |
|
Broadcom based SSB bus. |
|
|
|
If unsure, say N. |
|
|
|
config USB_OHCI_SH |
|
bool "OHCI support for SuperH USB controller (DEPRECATED)" |
|
depends on SUPERH |
|
select USB_OHCI_HCD_PLATFORM |
|
---help--- |
|
This option is deprecated now and the driver was removed, use |
|
USB_OHCI_HCD_PLATFORM instead. |
|
|
|
Enables support for the on-chip OHCI controller on the SuperH. |
|
If you use the PCI OHCI controller, this option is not necessary. |
|
|
|
config USB_OHCI_EXYNOS |
|
tristate "OHCI support for Samsung S5P/EXYNOS SoC Series" |
|
depends on ARCH_S5PV210 || ARCH_EXYNOS |
|
help |
|
Enable support for the Samsung Exynos SOC's on-chip OHCI controller. |
|
|
|
config USB_CNS3XXX_OHCI |
|
bool "Cavium CNS3XXX OHCI Module (DEPRECATED)" |
|
depends on ARCH_CNS3XXX |
|
select USB_OHCI_HCD_PLATFORM |
|
---help--- |
|
This option is deprecated now and the driver was removed, use |
|
USB_OHCI_HCD_PLATFORM instead. |
|
|
|
Enable support for the CNS3XXX SOC's on-chip OHCI controller. |
|
It is needed for low-speed USB 1.0 device support. |
|
|
|
config USB_OHCI_HCD_PLATFORM |
|
tristate "Generic OHCI driver for a platform device" |
|
default n |
|
---help--- |
|
Adds an OHCI host driver for a generic platform device, which |
|
provides a memory space and an irq. |
|
|
|
If unsure, say N. |
|
|
|
config USB_OCTEON_OHCI |
|
bool "Octeon on-chip OHCI support (DEPRECATED)" |
|
depends on CAVIUM_OCTEON_SOC |
|
default USB_OCTEON_EHCI |
|
select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN |
|
select USB_OHCI_LITTLE_ENDIAN |
|
select USB_OHCI_HCD_PLATFORM |
|
help |
|
This option is deprecated now and the driver was removed, use |
|
USB_OHCI_HCD_PLATFORM instead. |
|
|
|
Enable support for the Octeon II SOC's on-chip OHCI |
|
controller. It is needed for low-speed USB 1.0 device |
|
support. All CN6XXX based chips with USB are supported. |
|
|
|
endif # USB_OHCI_HCD |
|
|
|
config USB_UHCI_HCD |
|
tristate "UHCI HCD (most Intel and VIA) support" |
|
depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC |
|
---help--- |
|
The Universal Host Controller Interface is a standard by Intel for |
|
accessing the USB hardware in the PC (which is also called the USB |
|
host controller). If your USB host controller conforms to this |
|
standard, you may want to say Y, but see below. All recent boards |
|
with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX, |
|
i810, i820) conform to this standard. Also all VIA PCI chipsets |
|
(like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro |
|
133) and LEON/GRLIB SoCs with the GRUSBHC controller. |
|
If unsure, say Y. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called uhci-hcd. |
|
|
|
config USB_UHCI_SUPPORT_NON_PCI_HC |
|
bool |
|
default y if (SPARC_LEON || USB_UHCI_PLATFORM) |
|
|
|
config USB_UHCI_PLATFORM |
|
bool |
|
default y if ARCH_VT8500 |
|
|
|
config USB_UHCI_BIG_ENDIAN_MMIO |
|
bool |
|
default y if SPARC_LEON |
|
|
|
config USB_UHCI_BIG_ENDIAN_DESC |
|
bool |
|
default y if SPARC_LEON |
|
|
|
config USB_FHCI_HCD |
|
tristate "Freescale QE USB Host Controller support" |
|
depends on OF_GPIO && QE_GPIO && QUICC_ENGINE |
|
select FSL_GTM |
|
select QE_USB |
|
help |
|
This driver enables support for Freescale QE USB Host Controller |
|
(as found on MPC8360 and MPC8323 processors), the driver supports |
|
Full and Low Speed USB. |
|
|
|
config FHCI_DEBUG |
|
bool "Freescale QE USB Host Controller debug support" |
|
depends on USB_FHCI_HCD && DEBUG_FS |
|
help |
|
Say "y" to see some FHCI debug information and statistics |
|
through debugfs. |
|
|
|
config USB_U132_HCD |
|
tristate "Elan U132 Adapter Host Controller" |
|
depends on USB_FTDI_ELAN |
|
help |
|
The U132 adapter is a USB to CardBus adapter specifically designed |
|
for PC cards that contain an OHCI host controller. Typical PC cards |
|
are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132 |
|
adapter will *NOT* work with PC cards that do not contain an OHCI |
|
controller. |
|
|
|
For those PC cards that contain multiple OHCI controllers only the |
|
first one is used. |
|
|
|
The driver consists of two modules, the "ftdi-elan" module is a |
|
USB client driver that interfaces to the FTDI chip within ELAN's |
|
USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host |
|
controller driver that talks to the OHCI controller within the |
|
CardBus cards that are inserted in the U132 adapter. |
|
|
|
This driver has been tested with a CardBus OHCI USB adapter, and |
|
worked with a USB PEN Drive inserted into the first USB port of |
|
the PCCARD. A rather pointless thing to do, but useful for testing. |
|
|
|
It is safe to say M here. |
|
|
|
See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php> |
|
|
|
config USB_SL811_HCD |
|
tristate "SL811HS HCD support" |
|
help |
|
The SL811HS is a single-port USB controller that supports either |
|
host side or peripheral side roles. Enable this option if your |
|
board has this chip, and you want to use it as a host controller. |
|
If unsure, say N. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called sl811-hcd. |
|
|
|
config USB_SL811_HCD_ISO |
|
bool "partial ISO support" |
|
depends on USB_SL811_HCD |
|
help |
|
The driver doesn't support iso_frame_desc (yet), but for some simple |
|
devices that just queue one ISO frame per URB, then ISO transfers |
|
"should" work using the normal urb status fields. |
|
|
|
If unsure, say N. |
|
|
|
config USB_SL811_CS |
|
tristate "CF/PCMCIA support for SL811HS HCD" |
|
depends on USB_SL811_HCD && PCMCIA |
|
help |
|
Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC |
|
REX-CFU1U CF card (often used with PDAs). If unsure, say N. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called "sl811_cs". |
|
|
|
config USB_R8A66597_HCD |
|
tristate "R8A66597 HCD support" |
|
help |
|
The R8A66597 is a USB 2.0 host and peripheral controller. |
|
|
|
Enable this option if your board has this chip, and you want |
|
to use it as a host controller. If unsure, say N. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called r8a66597-hcd. |
|
|
|
config USB_RENESAS_USBHS_HCD |
|
tristate "Renesas USBHS HCD support" |
|
depends on USB_RENESAS_USBHS |
|
help |
|
The Renesas USBHS is a USB 2.0 host and peripheral controller. |
|
|
|
Enable this option if your board has this chip, and you want |
|
to use it as a host controller. If unsure, say N. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called renesas-usbhs. |
|
|
|
config USB_WHCI_HCD |
|
tristate "Wireless USB Host Controller Interface (WHCI) driver" |
|
depends on PCI && USB && UWB |
|
select USB_WUSB |
|
select UWB_WHCI |
|
help |
|
A driver for PCI-based Wireless USB Host Controllers that are |
|
compliant with the WHCI specification. |
|
|
|
To compile this driver a module, choose M here: the module |
|
will be called "whci-hcd". |
|
|
|
config USB_HWA_HCD |
|
tristate "Host Wire Adapter (HWA) driver" |
|
depends on USB && UWB |
|
select USB_WUSB |
|
select UWB_HWA |
|
help |
|
This driver enables you to connect Wireless USB devices to |
|
your system using a Host Wire Adaptor USB dongle. This is an |
|
UWB Radio Controller and WUSB Host Controller connected to |
|
your machine via USB (specified in WUSB1.0). |
|
|
|
To compile this driver a module, choose M here: the module |
|
will be called "hwa-hc". |
|
|
|
config USB_IMX21_HCD |
|
tristate "i.MX21 HCD support" |
|
depends on ARM && ARCH_MXC |
|
help |
|
This driver enables support for the on-chip USB host in the |
|
i.MX21 processor. |
|
|
|
To compile this driver as a module, choose M here: the |
|
module will be called "imx21-hcd". |
|
|
|
config USB_HCD_BCMA |
|
tristate "BCMA usb host driver" |
|
depends on BCMA |
|
select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD |
|
select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD |
|
help |
|
Enable support for the EHCI and OCHI host controller on an bcma bus. |
|
It converts the bcma driver into two platform device drivers |
|
for ehci and ohci. |
|
|
|
If unsure, say N. |
|
|
|
config USB_HCD_SSB |
|
tristate "SSB usb host driver" |
|
depends on SSB |
|
select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD |
|
select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD |
|
help |
|
Enable support for the EHCI and OCHI host controller on an bcma bus. |
|
It converts the bcma driver into two platform device drivers |
|
for ehci and ohci. |
|
|
|
If unsure, say N. |
|
|
|
config USB_HCD_TEST_MODE |
|
bool "HCD test mode support" |
|
---help--- |
|
Say 'Y' to enable additional software test modes that may be |
|
supported by the host controller drivers. |
|
|
|
One such test mode is the Embedded High-speed Host Electrical Test |
|
(EHSET) for EHCI host controller hardware, specifically the "Single |
|
Step Set Feature" test. Typically this will be enabled for On-the-Go |
|
or embedded hosts that need to undergo USB-IF compliance testing with |
|
the aid of special testing hardware. In the future, this may expand |
|
to include other tests that require support from a HCD driver. |
|
|
|
This option is of interest only to developers who need to validate |
|
their USB hardware designs. It is not needed for normal use. If |
|
unsure, say N.
|
|
|